Keeping Slate Roofs Weathertight on Listed Buildings

Why Slate Roofs Suffer More Than Most
A well-laid slate roof can last a century or more, but it is a covering held together by hundreds of small, individual decisions — each slate, each fixing, each lap — and that means it has hundreds of small points of potential failure. When gales sweep across the country, the damage rarely announces itself dramatically. A slater will tell you that the loudest storms are seldom the most damaging; it is the persistent, buffeting crosswinds that work away at the edges, lifting a slate just enough to break the nail, or driving rain up beneath a lap until the timber beneath is soaked.
On a listed building the stakes are higher. The roof is part of the building's historic fabric and its character. A crude repair can do more harm to the significance of a listed church or Georgian townhouse than the storm did, and it can be far harder to undo.
What to Look For After a Blow
Begin with binoculars from ground level — a pair of 10x42s is a slater's best friend after a storm. You are looking for anything that breaks the regularity of the courses:
- Slates lying in the gutter, or stacked against a hopper or downpipe where they have slid down the pitch.
- Dark gaps in an otherwise even course, which usually mean a slate is missing or has slipped out of position.
- Slates sitting proud, tilted, or visibly out of line with their neighbours.
- Cracked or holed slates, often caused by flying debris rather than wind alone.
- Fresh staining on the underside of eaves, on rafters visible from a loft, or on a ceiling below.
- Displaced lead flashings around chimneys, valleys, dormers and parapet gutters, which are the most common source of leaks even when no slate has moved.
Inside, shine a torch along the roof slopes from the loft. Water tracks leave a tide mark, and damp timbers smell musty. Look closely at the underside of battens and at the top of the wall plate, where leaks often first show.
Start With the Associated Works
Before anyone touches a slate, clear the gutters and hoppers. On a listed building these are often cast iron, and a blocked hopper will send water straight down the wall face and into the masonry, saturating the wall and eventually the roof structure. Check that downpipes are still securely bracketed — storms frequently pull them loose — and that the ground beneath discharges freely into a gully or soakaway. A surprising number of "roof leaks" reported after a gale are in fact overflowing rainwater goods.
Inspect the flashings too. Lead aprons, soakers, step flashings and secret gutters should be dressed tight and free of splits. Small, careful repairs to lead are almost always preferable to wholesale replacement, which risks damaging the surrounding slates.
Repairing Slipped, Missing and Broken Slates
The traditional approach is still the right one. Where access allows, a slater lifts the slates above the affected area just enough to reach the failure, and works from the top of the slope downwards so the covering is left weathertight behind them.
Slipped slates are usually re-hung on new fixings rather than simply pushed back. The old nail has failed for a reason — often corrosion of iron fixings or the breakdown of a timber batten — and simply tucking a slate back into position will not hold it through the next gale. Where a slate is beyond saving, it is replaced like-for-like: same material, same size, same thickness, same lap, and same method of fixing as the surrounding roof.
Nails matter enormously. Copper, silicon bronze or, where historically appropriate, hot-dipped galvanised nails are the sensible choices. Short, thin or bright steel fixings will fail long before the slate does. Where a slate has to be fixed without lifting the courses above, a slate hook or a tingles-and-mastic repair may be acceptable as an interim measure, but it should be recorded and reconsidered at the next proper repair.
Matching Materials on a Listed Building
Getting the slate right is the difference between a repair that disappears and one that shouts. If the roof is covered in Welsh heather blue slate, a paler, thicker imported slate patched into the middle of a slope will look exactly like what it is. Reputable salvage yards and suppliers of reclaimed slate can often match by size, thickness and colour, and a few spares kept in the church tower or loft are worth their weight in gold.
The same principle applies to every other element:
- Battens and laths — replace timber with the same species and scantling, and treat only where appropriate.
- Mortar — use a lime-based mix matched to the existing bedding and torching, never a hard cement-rich mix that traps moisture and cracks.
- Lead — code and weight should match the original, with proper laps and fixings.
- Surface finish — do not pressure-wash, seal or coat historic slate; gentle removal of moss with a soft brush is all that is needed.
Consent, Access and Finding the Right Hands
On most listed buildings, like-for-like repair using traditional materials does not require listed building consent, but any change to the appearance, materials or method of fixing very likely does. In churches, the faculty jurisdiction applies instead, and your Diocesan Advisory Committee will expect to see detail on slate source, fixings and any alterations. Speak to your conservation officer or DAC early — it is far easier to agree a specification than to justify work already done.
Finally, choose the person as carefully as the material. Look for a slater experienced with historic roofs, ask to see similar work, insist on a written specification and a method statement, and be wary of any quote that proposes to strip a whole slope when a dozen slates need attention. A good conservation repair is modest, reversible and almost invisible — which is exactly what the building deserves.

4 Comments