Conserving Historic Pews and Wooden Church Furniture

Conserving Historic Pews and Wooden Church Furniture

Why Old Oak Rewards Care

Most parish church furniture — pews, pulpits, reading desks, parclose screens, chests and alms boxes — was cut from oak, though you will also meet deal, pine, elm and the occasional walnut piece in later work. Oak that has stood in a cool building for three centuries is remarkably stable. Its grain has closed, its moisture content has settled to the rhythm of the seasons, and its surface has acquired a patina no workshop can fake. Conserving it is less about repair than restraint: hold the conditions steady, lift the dirt gently, and let the timber breathe. Anything you apply should be reversible, and anything you do should be the minimum needed.

Damp, Not Dust, Is the Real Enemy

Wood moves. It swells and shrinks as relative humidity changes, far more than most people expect. A steady 50–55% relative humidity, with gentle seasonal variation, keeps joints tight and panels flat. Big swings do the damage: joints open, veneer lifts, and historic paint cracks away from the surface.

Look for the sources before you look at the furniture:

  • Blocked or broken gutters, hoppers and downpipes above the nave.
  • Rising damp through a stone floor, which rots the feet of pews long before the tops show trouble.
  • High-level heating run for an hour on Sunday morning, warming the air, dropping the humidity and driving moisture into cold stone and cold timber.
  • Pew platforms, carpet and plastic sheeting, which trap moisture underneath.

Keep pews a hand's width clear of damp walls, rest them on slate or lead pads rather than directly on stone, and never wrap them in polythene. A couple of cheap data loggers recording temperature and humidity for a year will tell you more about the building than a surveyor's afternoon visit.

Cleaning: Soft, Dry and Patient

Dust is abrasive and it holds moisture against the surface, so removing it regularly is the single best thing you can do.

  • Use soft pony-hair or bristle brushes, and a vacuum on its lowest setting with a brush attachment. Stretch a piece of muslin over the nozzle to catch loose fragments from carved work.
  • Work from the top down: screens first, then backs and tops of pews, then seats, then the floor.
  • Cotton swabs and a wooden cocktail stick, used gently, will lift compacted wax and dirt from deep carving.

What to avoid matters just as much. Do not wash historic wood with water. Do not reach for methylated spirits, white spirit or proprietary cleaners without testing on an inconspicuous area and knowing what finish you are dealing with. Silicone polishes, spray waxes and aerosol furniture sprays leave a film that traps dirt, goes grey in time and is hard to remove. Bird droppings and candle wax need their own careful approach rather than a scrubbing brush.

Waxing and Reviving a Dry Surface

A good paste wax — a beeswax and carnauba blend, or a microcrystalline wax — will feed a dry, sound surface without sealing it. Apply very thin coats with a soft cloth, work the wax into the grain, let it haze, then buff it off with a bristle brush. Once or twice a year is plenty for furniture in daily use; pews in a cold church often need it far less.

Over-waxing is the commonest mistake. A thick film turns sticky, collects dust and blackens; if a surface feels tacky, remove excess wax rather than adding more. Avoid raw linseed oil and kitchen oils, which stay tacky, feed mould and darken unevenly. Varnished and French-polished pieces need only dusting and a sparing wax.

Pews, Pulpits and Screens

Loose joints should be re-glued with reversible animal glue by someone who knows historic joinery, not filled with modern resin filler. A creaking pew is often a floor problem rather than a furniture one, so check the boards and the pads beneath before tightening anything. Screens and pulpits are the most vulnerable pieces in the church: high, delicate and often carrying historic paint or gilding. Never lean a ladder against them; use a padded tower and keep tools off the ledges.

Woodworm deserves a mention. Fresh flight holes and fine frass mean active beetles. Many church pieces have been treated repeatedly over the years, and further chemical treatment is often unnecessary once the timber is dry. Identify the problem before reaching for a tin.

When to Call in a Conservator

Some jobs are beyond the volunteer rota: splitting panels, lifting veneer, failed structural joints, historic paint schemes, gilding, inlay and anything involving replacement timber. Take advice before work begins, keep photographs and a written record of everything done, and remember that significant work on a listed church normally needs a faculty and the views of the Diocesan Advisory Committee. Careful, patient housekeeping, recorded and repeated, will carry most of these buildings into their next century in better condition than they arrived.